A few typical issues, like e-liquid leakage or a burned coil, are available with most vape products on the market. When do these kinds of things happen? Is there a way to fix these issues and make sure they don't crop up again? Get all your questions answered and get some helpful hints in this article.
What causes e-liquid to leak, and what can be done to prevent it?
1. E-Liquid Spitting Issue
Spitting e-liquid is a common vaping occurrence and can happen with any brand of vaporizer. Here are a few things you can do to stay away from it.
For optimal results, inhale while simultaneously firing the battery. Vaping after pressing the battery's fire button for a few seconds might cause the drip tip to spew e-liquid into your mouth and make a noise.
After putting the tank aside for an extended period of time, check the coil to determine if there is an excess of juice in the central hole. In most cases, flooding the coil is the root cause of spitting. When the juice comes into touch with the hot coil, it pops, but it "spits" like a frying pan because it's so saturated. To fix this, turn the tank so that the drip tip is facing the floor and then swing the tank to release any excess e-juice. After that, wipe the drip tip and its surrounding area with some clean paper to remove any remaining e-juice.
Parts of the tank or components that are loose can also cause spitting. Make sure all of the tank's seals are in good working order, screw in all of the parts securely, and check that all of the accessories are there as well.
Spitting and a burned flavor might result from vaping without soaking the coil.
Vapor condensation, which resembles e-juice, may be visible on the drip tip or Top Fill area of the device. Spitting may result from these condensations. Consistently using a Q-tip or a clean paper towel to clean the drip tip, airflow hole, and top fill area is, thus, highly essential.
2.Leakage Caused by Tank Damaged Components
The anti-leak design of the tank or pod incorporates a silicone ring around the coil itself. Consequently, you should check its installation thoroughly at all times.
Before screwing in a screw-in coil, check its alignment to prevent cross-threading and the potential leakage of e-liquid.
Verify that there are no leaks or damage to the tank and coil seals. Take out and replace a gasket if it seems damaged. You can use the spare seal gaskets that come with most vape tanks for this.
Make sure the glass tube is free of cracks. A cracked glass tube could be an indication that the tank has been dropped. Also, make sure there is no looseness in the connection between the glass tube and the hardware of the tank.
3.Improper Filling of E-Liquid
One common cause of e-liquid leakage is overfilling. Leaks can occur if you fill your pod or tank with too much e-liquid. In most cases, the e-liquid will leak out of a vape tank or pod if the maximum fill level is exceeded. It is recommended to seal the air vents before opening the top cap to fill the tank. There should be a small gap at the top of every page. The liquid is held in place by a vacuum that is created by a small air gap.
It is recommended to seal the air vents before opening the top cap to fill the tank. Quickly and securely install the top cap after filling, and then open the air vents.
Be sure to fully close the pod's stopper after filling it. The Aspire Gotek X and Cyber G are two examples of vape pods that typically come with silicone stoppers. Always check the alignment and full insertion of the coil before using it, especially if your pod system is compatible with one.
Squeezing the e-liquid into the central airflow channel is another typical error made by newcomers. You should avoid filling the central chimney of the coil with liquid. This chimney forms the airway for your vapour and extends into the mouthpiece. After filling, the liquid will flow directly from the tank's bottom airflow ports through the coil.
How to avoid coil burnt issue?
1. Choose your e-liquid wisely
Using the right e-liquid can help extend the life of your coils.Carefully select the e-liquid that corresponds to your coil type.
While e-liquids with a high sugar or sweetener content taste great, they shorten the life of the coils because they quickly gunk up and caramelize. The juice turns a darker shade due to the caramelized coils that color it and reduce their lifespan.
2.Saturate coil with e-liquid properly
To avoid damaging the coil, fill it up with e-liquid before you start vaping.
Allow the coil to soak up the e-liquid by letting the tank sit for approximately 5 minutes after filling it. For an improved and quicker experience, some people prefer to add a few drops of e-liquid to the wicking cotton of the coil before placing it in the tank. You may take a puff after it has sat for a while, but hold off on pressing the fire button. The liquid will be more easily drawn into the coil if this is done.
Additionally, make sure to refill the tank before the e-liquid inside runs out entirely.
After the initial few puffs of a brand-new coil, the flavor will become increasingly pure.